The Mondeo remote control key set

Frist  let the Mondeo car’s All the doors are closed,

Than The ignition switch is opened and closed 4 times, at this time the system will sound.

And Press locking, unlocking or trunk button, wait for the beep.

So In 10S repeat the above procedure to set the rest of the remote control.

The ignition switch is turned on,

exit setup, is ok!

Autosuning  provides a variety of matching the key equipment and instruments, commonly used: SBB key programmer; T300 KEY; MVP AD900; Car key programmer; AK500 Benz key programmer and other instruments, welcome to contact: info@autosuning.com, or to our website: http://www.autosuning.com about the new car product information!

Calibration method of pulling needles odometer

The first point: you must know what form of motor can pull what motor can not be pulled and which motor pull broken can repair the pull bad repair not so you can according to the risk and technical content to the appropriate fees charged to customers.

A built-in reduction gear of the stepper motor is most plastic shell coil winding [ i.e. in appearance with neither metal shell not see

Coil but do not see gossamer ]. This motor pull on the hand when can not worry, his shaft is pull it out

The two coil winding is simulated motor [ for example ] and Lancer oil table motor coil winding of the step motor [ for example ] there is a horse 6 motor with gossamer instrumentation motor [ such as BMW X5 electric instrument ] several types of this motor in the needle must be careful when.

Second; we finish pull hand was required after inserting needle which is also a problem

Many industry friends all know for those of the motor itself with limiting motor inserting table for position is a very easy thing. But for those without their own limit can be 360 °rotating motor in unplug needle after the not so good for the location, below tell you several ways;

The first method is to pull out the needle before you hand over the dial on the limiting device for hands free to stop at a location and then in the position to take a mark in accordance with the time to get back on the OK in situ

The second method is to do mark pull directly loaded when the instrument is electrified all the motor will return to the initial state of readiness for this in all hand alignment dial low inserted on the OK music

The third method is fitted to the car up to the hand [ such as you don't know the car how much oil to oil table pointer alignment, then we need to switch off the ignition, and then pull the fuel tank sensor plug and then turn the ignition switch and oil motor is the location of the pointer in the empty box is inserted into the empty position on the OK Le installation temperature table pointer could also be pulled out temperature sensor plug and then plug in the alignment of the pointer low ]

Mounted tachometer pointer when you can start the vehicle in the engine idle time alignment between 800-900 with OK

  Autosuning can provide you the automobile odometer; related to obd2 diagnosis, testing tools, a wide variety, low prices, one-stop to satisfy all your requirements; welcome to contact, or to our website: http://www.autosuning.com understanding of the latest automobile product information!

Repair of BMW X5E39 chassis instrumentation attention

A few days ago, the Division I repair a BMWX5 instrument, pull the hand inside the driver is the ULOQ2003 driving light emitting diode, such as steering gear display lamp, lights, hand out after, if the return is not good, not to repair, electrical instrument down, the motor is inserted on the pointer shaft, gently fall a few times, OK, can be normal use.

Autosuning company as the industry vanguard, pioneering and innovative, forge ahead, in OBD diagnostic category, the extraordinary accomplishments, has become the industry 's rising star。(edit by obd2)

Citroen car maintenance lights zero

Citroen Picasso dashboard maintenance light V19 wrench shape, each connected to the ignition switch 2S can shine, and the odometer display to the next maintenance also remaining mileage, after 2S disappeared.

Picasso cars over the maintenance period without maintenance, each connected to the ignition switch 5S, maintenance lights and has more than maintenance provisions of miles will display, 5S odometer display normal values, but maintenance lights shining.

For the first time in maintenance and periodic maintenance, the need for maintenance lamp zero. As for other mileage, not to maintain the light return-to-zero operation, otherwise the prompt maintenance mileage and really should be maintenance mileage on not on.

To remind the user when more than maintenance mileage maintenance lights shining, don't let it out to zero, must undertake the maintenance after the return to zero, so that maintenance of the lights. Maintenance lights zero method is as follows: the ignition switch to OFF position.

Pressed by a finger length zero button Q real. The ignition switch to ON position. Mileage display 10, 9, 8 ... ... Counting down until 0. Undo the mileage zero button Q, switch off the ignition, remove the ignition key, maintenance lights

   The above article, by autosuning, finishing with: http://www.autosuning.com, welcome to reprint, please keep the link.

  Autosuning is the industry's advanced model, due to the stable performance, reliable quality, business integrity management, Monash Guangsian, we have access to a wide range of customer recognition and highly dependent on, welcome friends from all circles to visit Autosuning Co., LTD visit, guidance and business negotiation

BMW car maintenance lights zero method

The new BMW 7 Series Sedan ( E65 ) after changing engine oil should be zero operation:

1, insert the ignition key, don't step on the brake pedal, press the START/STOPENGINE button on the left side of the ignition key.

2, hold the instrument the top left of the zero button, about 8s after the release, instrument left top LCD display: RETURN ( rollback); BR.FLUID8MTHS; ENG.OIL30TKM; FR.BRAKE40TKM; R.BRAKE40TKM; VEH.CHIK50TKM; MICROFIL60TKM; SPKPLUGS60TKM; COOLANT32MTHS.

Note: when exceeding the prescribed mileage or cycle, the liquid crystal display area displays the maintenance information, maintenance information is returned to zero, zero main menu will be displayed "! " Remind the words. For example, front brake pads exceed the prescribed time or replacement without zero operation, the instrument will display " Fr.Brake40Tkm! ".

3, click the zero button ( or press the steering lamp switch on the B, C two buttons ), select ENG.OIL30TKM, and then hold down to zero button, until the meter right area displayed on the screen, then press " RETURNRESETENG.OIL " zero button to select the "RESETENG.OIL", and press again to zero button and keep, until the screen display ENG.OILRESETOK, brake alarm lamp zero program is completed.

I  n 4, when started again, the instrument will display " after sale service 30000 km moment ".

Autosuning is the industry's advanced model, due to the stable performance, reliable quality, business integrity management, Monash Guangsian, we have access to a wide range of customer recognition and highly dependent on, welcome friends from all circles to visit Autosuning Co., LTD visit, guidance and business negotiation(obd2)